色婷婷五月综合亚洲小说-亚洲精品蜜桃久久久久久-亚洲欧美日韩精品久久-国精品午夜福利视频不卡757

當前位置:首頁-新聞資訊

鋁板模具生產質量的提升需要怎么做?

來源:http://m.gdjsdtc.com/ 發布時間:2018-03-19

1、在使用鋁板生產模具的時候,需要選擇合適的加熱溫度。要嚴格控制擠壓錠坯的合金成分。目前一般企業要求鑄錠晶粒度達到一級標準,以增強塑性和減少各項異性。
1. When using the aluminum plate to produce the mold, it is necessary to choose the appropriate heating temperature. The alloy components of the extruded ingot must be strictly controlled. At present, the general enterprises require the grain size of ingot to reach the first grade standard, in order to enhance the plasticity and reduce the various heterosexual.
2、鋁板生產模具上機前工作帶必須經過研磨拋光,工作帶一般要求拋光至鏡面。對模具工作帶的平面度和垂直度裝配前要進行檢查。
2. The front work belt of the aluminum sheet production die must be polished and polished, and the working belt is generally required to be polished to the mirror. Check for the flatness and perpendicularity of the die working belt before assembly.
3、鋁板生產模具保溫時間一般在2-3小時左右,但不能超過8小時,否則模具工作帶氮化層硬度會降低而導致上機時不耐磨引起型材表面粗糙,嚴重的會引起劃線等缺陷。

鋁板生產廠家
3, the aluminum plate production mold holding time is generally about 2-3 hours, but it can not exceed 8 hours, otherwise the mold working nitrided layer hardness will decrease, resulting in the machine wear-resisting, causing rough surface profile, and serious will cause the marking and other defects.
4、進行擠壓生產前,需對型材截面進行充分計算,根據型材截面的復雜程度,壁厚大小以及擠壓系數λ來確定擠壓機噸位大小。
4, before extrusion production, we need to fully calculate the cross section of the section, and determine the tonnage size of the extruder according to the complexity of the section section, the thickness of the wall and the extrusion coefficient.
5、鋁板生產模具卸模后,此時模具溫度在500°C以上,如果立即浸入堿水中,由于堿水溫度要比模具溫度低得多,如果模具溫度下降迅速,模具極易發生開裂現象。正確方法是等卸模后將模具在空氣中放置到100°-150°C再浸入堿水中。
5, when the aluminum plate production mold is unloaded, the mold temperature will be above 500 degree C. If immersion in alkali water immediately, because the temperature of alkali water is much lower than that of the mold, if the mold temperature drops rapidly, the mold will easily crack. The correct method is to put the mold in the air to 100 -150 C and then immerse in the alkali water after the mold is unloaded.
我們專門為您提供鋁板生產廠家服務,想要了解更多的資訊內容,歡迎訪問我們的網站: http://m.gdjsdtc.com 的知識為您提供貼心的服務。
We provide you with aluminum plate manufacturer services, want to know more information content, welcome to our website: http://m.gdjsdtc.com professional knowledge to provide you with intimate service.

主站蜘蛛池模板: 免费观看无遮挡www的视频| 朝鲜女子内射杂交bbw| 又大又长粗又爽又黄少妇视频| 久久久无码精品亚洲日韩蜜桃| 精品国产一区二区三区av性色| 亚洲av无码国产精品久久| 高清一区二区三区日本久| 亚洲狠狠婷婷综合久久| 久久人人爽天天玩人人妻精品 | 狠狠色噜噜狠狠狠狠888奇禾| 精品少妇无码av无码专区| 久久天堂av综合色无码专区| www夜片内射视频日韩精品成人 | 老熟女多次高潮露脸视频| 国内精品视频一区二区三区| 麻豆精品一区二区综合av| 把插八插露脸对白内射| 亚洲精品午夜国产va久久成人| 97se亚洲国产综合自在线| 艳妇交换俱乐部| 99精品视频九九精品视频| 99热这里有精品| 人妻丰满被色诱中文字幕| 丰满人妻被黑人猛烈进入| 日本人成网站18禁止久久影院| 人妻换人妻仑乱| 日韩一区二区三区无码影院| 亚洲av永久无码精品秋霞电影秋| 欧美囗交xx×bbb视频| 大屁股人妻女教师撅着屁股| 日本牲交大片无遮挡| 亚洲理论电影在线观看| 国产av一区二区三区无码野战| 亚洲欧美国产精品久久| 中文字幕日韩一区二区三区不卡 | 精品人妻人人做人人爽| 国产乱理伦片在线观看| 国产欧美日韩中文久久| 国产八十老太另类| 天天摸天天透天天添| 精品成人av一区二区三区|